• Home

• Copy Programs
  • NEW - Deluxe Copy Center
  • Convenience Copy Centers
  • Get Product Information

• About Us
  • Fact Sheet
  • Executive Management
  • Newsletter

• Support
  • Technical Support
  • Customer Service
  • Machine Operating Tips
    • Konica Model 2223
    • Konica Model 2230
    • TRM Model 9218
    • Copy Machine Vend Towers
  • Machine Troubleshooting
    • Konica Model 2223
    • Konica Model 2230
    • TRM Model 9218
    • Copy Machine Vend Towers
  • FAQs
    • Contract Information
    • How To Read Your Meter

• Contact Us
  • Fact Sheet
  • Contact Us

• Customers
  • Customer Intranet
    • Member Sign On
  • FAQs
    • Contract Information
    • How To Read Your Meter
  • Contact Us
  • Newsletter

800.927.0979

Konica Model 2223

• Location of the On/Off Switch
• Placement of Originals on Glass
• Changing Paper Size (trays)
• Adjusting Size (enlarge/reduce)
• Lighten/darken Copies:
• Loading Paper
• How to use 11 x 17 Paper:
• Loading Toner
• Taking a Meter Reading from the Copier:

Quick Fact: Location of the On/off Switch

1. The On/Off switch is located on the inside of the copier, under the control panel.
2. Press the two Release buttons on either side of the front cover.
3. The front cover, along with the control panel will swing down (like an oven door). The On/Off switch is located in the top left side.

Quick Fact: Placement of originals on the glass

1. For letter-size copies, place the original in a vertical position.
2. For legal-size copies, place the original in a horizontal position.

Procedure: Changing paper size (trays):

1. Press the "Copy Size" button to the right of the digital panel.
2. Press the button until you have selected the appropriate paper size.
3. To cancel, press the Reset button. (Reset will cause the copier to go back to 8.5 x 11 paper.)

Procedure: Adjusting Size (enlarge/reduce)

1. Two modes are available, "Manual" and "Preset". The Mode button allows toggling between the two modes.
2. On Manual mode, enlargement and reduction can be selected in 1% increments by pressing the buttons with the up and down arrows.
3. On Preset mode, pressing the up arrow will enlarge to preset increments of 129%, 155%, and 200%. Press the down arrow will reduce to preset increments of 77%, 65%, and 50%.
4. To cancel in either mode, press the Reset button.

Procedure: Lighten/darken copies

1. Press the left arrow (lighten) or right arrow (darken) that are labeled "Copy Density" located directly below the digital panel.
2. To cancel, press the Reset button.

Procedure: Loading Paper

1. After removing the paper from the package, open drawer 1 (top) for 8 x 11 or drawer 2 (bottom) for 8 x 14 paper.
2. On the right-hand side of the drawer (facing the copier) are two white plastic tabs that hold the paper in place. Make sure all the paper is under the tabs.
3. Close the drawer.

Procedure: How to use 11 x 17 Paper

1. Insert the 11 x 17 paper into the bypass tray.
2. Select the bypass option through the paper size selector.

Procedure: Loading Toner

CAUTION: The copy machine will indicate when toner needs to be replaced. Never "top-off" toner or load it unless the copier indicates the toner needs to be replaced. If the copies are light, but the machine is not indicating that the toner needs to be replaced, please call 1-800-877-2679 for service.

WARNING: Before adding toner, carefully read the directions and safety information included with the toner cartridge. Keep toner away from children. Although toner is non-toxic, do not inhale it or allow it to enter your eyes. If toner comes in contact with eyes, consult your physician.

1. Open the front panel of the copier. The toner receptacle runs along the top of the copier.
2. Lift the green lid up. The toner bottle has a cylindrical body and a square base.
3. The toner may have settled, so shake the new toner cartridge well before loading.
4. The base of the toner bottle has an exterior plastic cap. Remove this cap.
   
   CAUTION: The toner bottle will also have an interior plastic cap. Do Not Remove the Interior Plastic Cap.
   
   
5. Along the base (opposite the label side) is a depressed lip. This fits under a similar raised lip on the toner receptacle.
6. Once the toner bottle is in place, slide the green lever to the left.
   
   CAUTION: Do Not Squeeze the Toner Bottle. This can cause toner clouds and is difficult to clean up.
   
   
7. The toner bottle may take several minutes to empty. If some toner appears compacted at the top, gently tap the top or side of the bottle.
8. Once the bottle is empty, slid the green lever to the right and remove the bottle.
9. Lower the lid and close the front cover.

Procedure: Taking a Meter Reading from the Copier:

1. Press the P then Stop/Clear buttons and hold both buttons down. The meter reading(s) will appear on the digital panel. Once reading(s) appear, you can release the buttons.
2. When you are done, press the Reset button.

Back to Top